MCP6242T-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6242 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Nominal Supply Current | 50μA |
| Output Current | 23mA |
| Current - Supply | 50μA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 550 kHz |
| Unity Gain BW-Nom | 550 kHz |
| Voltage Gain | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 23mA |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Power | NO |
| Height Seated (Max) | 1.55mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6242T-E/SN Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. Op amps are General Purpose types of amplifier on the chip. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. There have been a total of 8 terminations over the past year. A total of 8 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 5V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. In total, the buffer amplifier consists of 8 pins. With regard to input offset voltage, instrumentation amplifier is rated at 5mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. Keeping the voltage gain at 110dB is the best course of action. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. There is a rating of 2 for the operating supply voltage of the buffer op amp. An buffer amplifier is packed in a TAPE AND REEL-shape according to the design. It is recommended that you use an 50μA power supply with this electrical part in order for it to operate correctly.
MCP6242T-E/SN Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6242T-E/SN Applications
There are a lot of Microchip Technology MCP6242T-E/SN Instrumentational OP Amps applications.
- Video conversion and routing
- Laptop
- Measurements of Wheatstone bridge
- RF cable systems
- Navigation
- Medical instruments
- Differentiator circuits
- Professional videography
- Power transmission
- Signal filtering
