Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
14 |
Operating Temperature |
-40°C~125°C |
Packaging |
Tube |
Published |
2008 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Operational Amplifier |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
MCP6244 |
Pin Count |
14 |
Output Type |
Rail-to-Rail |
Power Supplies |
2/5V |
Number of Channels |
4 |
Operating Supply Current |
50μA |
Nominal Supply Current |
50μA |
Output Current |
23mA |
Slew Rate |
0.3V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
60 dB |
Current - Input Bias |
1pA |
Voltage - Supply, Single/Dual (±) |
1.8V~5.5V |
Output Current per Channel |
23mA |
Input Offset Voltage (Vos) |
5mV |
Bandwidth |
550 kHz |
Unity Gain BW-Nom |
550 kHz |
Voltage Gain |
110dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
7V |
Low-Bias |
YES |
Micropower |
YES |
Height |
900μm |
Length |
5mm |
Width |
4.4mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MCP6244-E/ST Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case package that contains the instrumentation amplifiers. An op amp of this type is a General Purpose-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. The number of terminations approaches 14. It consists of a total of 14 pins in total. Please take in mind that op amp should be run at 5V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 14 pins are located on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 5mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. An 50μA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 110dB. On the buffer amps, there are 4 channels that can be used. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals.
MCP6244-E/ST Features
14 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6244-E/ST Applications
There are a lot of Microchip Technology MCP6244-E/ST Instrumentational OP Amps applications.
- Fission chambers
- Power transmission
- Differentiator circuits
- Radar
- Medical instruments
- Professional videography
- Mobile phone
- Signal operation
- Video data acquisition
- Portable electronic products powered by batteries