MCP625T-E/UN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | mCal Technology |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP625 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Nominal Supply Current | 2.5mA |
| Output Current | 70mA |
| Current - Supply | 2.5mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 200μV |
| Gain Bandwidth Product | 20MHz |
| Unity Gain BW-Nom | 20000 kHz |
| Voltage Gain | 126dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Current - Output / Channel | 70mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP625T-E/UN Overview
The linear amplifier is packaged in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) case. Buffer amps of this type are called General Purpose-types. A Tape & Reel (TR) case is used for delivering the op amp. A total of 10 terminations have been reported in the past few weeks. Buffer amplifier has a total of 10 pins. Please take in mind that op amp should be run at 2.5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 10 pins. In terms of input offset voltage, operational amplifier rates 200μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . 126dB should remain the voltage gain. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. For the operating supply voltage of the op amp ic, there is a rating of 2. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. We recommend that you use this electronic part with an 2.5mA supply in order to get the best performance from it. In this case, mCal Technology represents the instrumentation amplifiers' series number.
MCP625T-E/UN Features
10 Pins
supply voltage of 2.5V
126dB voltage gain
Output Type: Rail-to-Rail
MCP625T-E/UN Applications
There are a lot of Microchip Technology MCP625T-E/UN Instrumentational OP Amps applications.
- Proportional operation circuits
- Radiation thermometry transducers
- Medical imaging
- Addition operation circuits
- Car stereo
- E-book readers
- RF cable systems
- Signal operation
- Ultrasound transducers
- Vehicle electronics
