MCP6271T-E/OT
| Parameters | |
|---|---|
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6271 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Nominal Supply Current | 170μA |
| Output Current | 25mA |
| Current - Supply | 170μA |
| Slew Rate | 0.9V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 25mA |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
MCP6271T-E/OT Overview
In order to protect the op amps, a SC-74A, SOT-753 case is used. Buffer amps of this type are called General Purpose-types. As far as the packaging is concerned, buffer op amp is delivered in a Cut Tape (CT) case. There is a growing number of terminations approaching the number of 5. Buffer amplifier has a total of 5 pins on it. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. It should be noted that this op amp is a type of Operational Amplifier device. There are 5 pins on this chip. With regard to input offset voltage, instrumentation amplifier is rated at 3mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureKeeping the voltage gain at 110dB is the best course of action. Buffer op amp is equipped with 1 channels on the device. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. For optimal performance, this electrical part should be connected to a supply with a current of 170μA.
MCP6271T-E/OT Features
5 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6271T-E/OT Applications
There are a lot of Microchip Technology MCP6271T-E/OT Instrumentational OP Amps applications.
- Digital cameras
- Laptop
- Power transmission
- earphone
- pH (acidity)
- Semiconductor detectors
- Voltage regulation circuit
- Integrator circuits
- Television
- Signal transformation
