MCP6275-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6275 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Operating Supply Current | 170μA |
| Nominal Supply Current | 170μA |
| Output Current | 25mA |
| Quiescent Current | 170μA |
| Slew Rate | 0.9V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2V~6V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Height | 1.25mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6275-E/SN Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. A General Purpose-type buffer amplifier is shown here. The case in which buffer amplifier is delivered is called a Tube case. The number of terminations approaches 8. There are a total of 8 pins on this op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. It should be noted that this op amp is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. In terms of the input offset voltage, instrumentation amplifier rates at 3mV. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . Using a supply current of 170μA , this buffer op amp will be able to operate. The voltage gain should stay at 110dB. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. It is possible to count 2 elements on this buffer amplifier. Linear amplifier has a quiescent current of 170μA.
MCP6275-E/SN Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6275-E/SN Applications
There are a lot of Microchip Technology MCP6275-E/SN Instrumentational OP Amps applications.
- Band-pass filter
- Vehicle electronics
- Digital cameras
- Signal operation
- Weak signal detection
- Division circuits
- Thermocouples
- High-frequency data acquisition systems
- Semiconductor detectors
- Oscilloscopes
