MCP6275T-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6275 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Nominal Supply Current | 170μA |
| Output Current | 25mA |
| Current - Supply | 170μA |
| Slew Rate | 0.9V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 25mA |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6275T-E/SN Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. General Purpose-type instrumentation amplifiers are used in this application. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. Buffer amplifier has a total of 8 pins on it. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 8 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. This electronic part is best mounted with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureThere should be no change in the voltage gain. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. The total number of elements in this buffer amplifier is 2. TAPE AND REEL is adopted to pack the instrumentation amplifier. There is a recommendation that this electrical part be used with a supply with 170μA current rating.
MCP6275T-E/SN Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6275T-E/SN Applications
There are a lot of Microchip Technology MCP6275T-E/SN Instrumentational OP Amps applications.
- Home audio systems
- Measurements of Wheatstone bridge
- Laptop
- Video conversion and routing
- Industrial applications including automation
- Medical instruments
- Image computer boards
- Automotive sensors
- Micro signal measurement
- Instrumentation
