MCP6282T-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6282 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Nominal Supply Current | 450μA |
| Output Current | 25mA |
| Current - Supply | 450μA |
| Slew Rate | 2.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.2V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 25mA |
| Low-Bias | YES |
| Micropower | YES |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6282T-E/SN Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. An op amp ic of the General Purpose type. A Tape & Reel (TR) case is used to deliver the buffer op amp. In recent months, the number of terminations has approached 8. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. There are 8 pins on this chip. Regarding input offset voltage, op amp rates 3mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureKeeping the voltage gain at 110dB is the best course of action. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. There are 2 elements in this buffer amplifier. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. This electronic part is recommended to be used with an 450μA supply for best performance.
MCP6282T-E/SN Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6282T-E/SN Applications
There are a lot of Microchip Technology MCP6282T-E/SN Instrumentational OP Amps applications.
- Digital cameras
- Wireless base stations
- Commercial audio systems
- Vehicle electronics
- Biopotential
- Automation control systems
- Test equipment
- Communication
- Precision measurement
- Laptop
