MCP6283T-E/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6283 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Power Supplies | 2.5/5V |
| Operating Supply Current | 450μA |
| Nominal Supply Current | 450μA |
| Output Current | 25mA |
| Slew Rate | 2.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.2V~6V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6283T-E/MS Overview
It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. An op amp ic of the General Purpose type. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins. This linear amplifier should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. There are 8 pins on this chip. Op amp rates 3mV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureAn 450μA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 110dB for the time being. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. There is a rating of 1 for the operating supply voltage of the buffer op amp. It is used TAPE AND REEL to pack the op amps.
MCP6283T-E/MS Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6283T-E/MS Applications
There are a lot of Microchip Technology MCP6283T-E/MS Instrumentational OP Amps applications.
- Video conversion and routing
- ECG equipment
- Test equipment
- Displayers for aircraft and air transportation control systems
- Active probe
- earphone
- Image computer boards
- Television broadcasting equipment
- Home audio systems
- High/low-pass filter circuit
