MCP6283T-E/SN
| Parameters | |
|---|---|
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.2V~6V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6283 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Power Supplies | 2.5/5V |
| Operating Supply Current | 450μA |
| Nominal Supply Current | 450μA |
| Output Current | 25mA |
| Slew Rate | 2.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
MCP6283T-E/SN Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. General Purpose-type instrumentation amplifiers are used in this application. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. We are approaching the 8h termination of the year. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 5V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are located on the operational amplifiers. There is an input offset voltage of 3mV for this buffer op amp. This electronic part is best mounted with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . As long as the supply current of the chip does not exceed 450μA, this op amp ic can operate. It is a member of the 110dB's 110dB family. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. This linear amplifier has a total of 1 elements. TAPE AND REEL is adopted to pack the instrumentation amplifier.
MCP6283T-E/SN Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6283T-E/SN Applications
There are a lot of Microchip Technology MCP6283T-E/SN Instrumentational OP Amps applications.
- Wireless base stations
- Navigation
- Displayers for aircraft and air transportation control systems
- single/dual op amp sum and difference circuits
- Test equipment
- Industrial control system
- Vehicle electronics
- Fission chambers
- ECG equipment
- Test and measurement instruments
