MCP6285T-E/SN
| Parameters | |
|---|---|
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6285 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Nominal Supply Current | 450μA |
| Output Current | 25mA |
| Current - Supply | 450μA |
| Slew Rate | 2.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.2V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 25mA |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
MCP6285T-E/SN Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. The instrumentation amplifier in this picture is of the General Purpose-type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 8. A total of 8 pins are attached to buffer op amp. I would like to remind you that this buffer op amp should be powered by an 5V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. It has 8 pins that make up the linear amplifier. Regarding input offset voltage, buffer amplifier rates 3mV voltage. This electronic part is best mounted with type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . 110dB should remain the voltage gain. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The linear amplifier consists of 2 different elements in total. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. For optimal performance, this electrical part should be connected to a supply with a current of 450μA.
MCP6285T-E/SN Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6285T-E/SN Applications
There are a lot of Microchip Technology MCP6285T-E/SN Instrumentational OP Amps applications.
- Signal amplification
- Blood pressure sensors
- Medical instruments
- Instrumentation
- Non-polarized electrodes
- Weighing systems
- Automotive sensors
- Medical imaging
- Tablets
- Power transmission
