MCP629-E/ML
| Parameters | |
|---|---|
| Output Current | 70mA |
| Current - Supply | 2.5mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 20MHz |
| Unity Gain BW-Nom | 20000 kHz |
| Voltage Gain | 126dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Current - Output / Channel | 70mA |
| Low-Bias | YES |
| Height | 950μm |
| Length | 4mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2010 |
| Series | mCal Technology |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP629 |
| Pin Count | 16 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Nominal Supply Current | 2.5mA |
MCP629-E/ML Overview
There is a 16-VQFN Exposed Pad case in which the instrumentation amplifier is packaged. The instrumentation amplifier in this picture is of the General Purpose-type. A Tube case is used to deliver the buffer op amp. It is estimated that there will be 16 terminations in the next few months. The total number of pins on linear amplifier is 16. I would like to remind you that this buffer op amp should be powered by an 2.5V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. There are 16 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 200μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . It is a member of the 126dB's 126dB family. The op amp ic has 4 channels on it. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. As a recommendation, this electronic component should be used with a power supply that can deliver 2.5mA. mCal Technology is the number that corresponds to the series of the buffer op amp.
MCP629-E/ML Features
16 Pins
supply voltage of 2.5V
126dB voltage gain
Output Type: Rail-to-Rail
MCP629-E/ML Applications
There are a lot of Microchip Technology MCP629-E/ML Instrumentational OP Amps applications.
- Computer workstations
- Television
- MP3
- Subtraction operation circuits
- Home audio systems
- Image computer boards
- Micro signal measurement
- Precision measurement
- E-book readers
- Division circuits
