MCP6291-E/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6291 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2.5/5V |
| Number of Channels | 1 |
| Nominal Supply Current | 1mA |
| Output Current | 25mA |
| Current - Supply | 1mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 25mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
MCP6291-E/MS Overview
In the package, you will find a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. The op amp is delivered to you in a Tube case. The number of terminations approaches 8. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. Linear amplifier includes 8 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. With regard to operating temperature, this op amp functions well at -40°C~125°C. Voltage gain should remain at 110dB. There are 1 channels on the operational amplifiers. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. In order to ensure optimal performance, an 1mA supply is recommended for this electrical component.
MCP6291-E/MS Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6291-E/MS Applications
There are a lot of Microchip Technology MCP6291-E/MS Instrumentational OP Amps applications.
- Large motor controllers
- Television broadcasting equipment
- Laptop
- Multiplication circuits
- Active probe
- PDA
- Professional videography
- Digital cameras
- Band-pass filter
- High gain DC amplifier
