MCP6291T-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6291 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Power Supplies | 2.5/5V |
| Nominal Supply Current | 1mA |
| Output Current | 25mA |
| Current - Supply | 1mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 25mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6291T-E/SN Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. An op amp ic of the General Purpose type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. Linear amplifier has a total of 8 pins. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. This electronic part is best mounted with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. 110dB should remain the voltage gain. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The buffer op amp is rated for an operating voltage of 1 when it comes to the power supply. As a result of this, the buffer amplifier is packed in TAPE AND REEL. To run supply current of buffer amplifier under 1mA.
MCP6291T-E/SN Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6291T-E/SN Applications
There are a lot of Microchip Technology MCP6291T-E/SN Instrumentational OP Amps applications.
- Vehicle electronics
- Proportional operation circuits
- Wireless base stations
- Voltage regulation circuit
- Weak signal detection
- Oscilloscopes
- Thermocouples
- Fast A/D and D/A converters
- Automotive sensors
- Video amplifiers
