MCP6292T-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6292 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Nominal Supply Current | 1mA |
| Output Current | 25mA |
| Current - Supply | 1mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 25mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6292T-E/SN Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. Buffer amps of this type are called General Purpose-types. A Tape & Reel (TR) case is used to deliver the buffer op amp. There is a growing number of terminations approaching the number of 8. In total, there are 8 pins on this op amp ic. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 3mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. 110dB should be the voltage gain. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. There are a total of 2 elements in this linear amplifier. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted. A supply of 1mA or higher is recommended for use with this electronic part.
MCP6292T-E/SN Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6292T-E/SN Applications
There are a lot of Microchip Technology MCP6292T-E/SN Instrumentational OP Amps applications.
- E-book readers
- Signal operation
- Active probe
- Navigation
- Addition operation circuits
- Professional videography
- Integrator circuits
- Power transmission
- Comparator
- MP3
