MCP6293T-E/CH
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6293 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2.5/5V |
| Number of Channels | 1 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 1mA |
| Output Current | 25mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~6V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6293T-E/CH Overview
It is packaged in an SOT-23-6-case that protects the operational amplifiers from damage. Op amps are General Purpose types of amplifier on the chip. In the case of Cut Tape (CT) cases, linear amplifier will be delivered. The number of terminations is approaching the 6 mark. Buffer amplifier has a total of 6 pins on it. Please take in mind that op amp should be run at 5V. Instrumentation amplifier is a part of Operational Amplifier. 6 pins are included on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 3mV. This electronic part is best mounted with type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . Operational amplifier can operate supply current at 1mA. The voltage gain should stay at 110dB. On the buffer amps, there are 1 channels that can be used. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
MCP6293T-E/CH Features
6 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6293T-E/CH Applications
There are a lot of Microchip Technology MCP6293T-E/CH Instrumentational OP Amps applications.
- Voltage regulation circuit
- Thermocouples
- Power transmission
- Automation control systems
- RF cable systems
- Integrator circuits
- Automatic control
- Image computer boards
- Signal operation
- Video computer boards
