MCP632-E/MF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP632 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Operating Supply Current | 2.5mA |
| Nominal Supply Current | 2.5mA |
| Output Current | 70mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 63 dB |
| Current - Input Bias | 4pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 8mV |
| Bandwidth | 24MHz |
| Unity Gain BW-Nom | 24000 kHz |
| Voltage Gain | 124dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Voltage - Input Offset | 1.8mV |
| Low-Bias | YES |
| Micropower | NO |
| Max Frequency | 1MHz |
| Programmable Power | NO |
| Height | 950μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP632-E/MF Overview
Packaged in a 8-VDFN Exposed Pad case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Tube case. In recent months, the number of terminations has approached 8. The total number of pins on linear amplifier is 8. It is important to remember that this op amp should be operated at a voltage of 2.5V volts. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 8 pins are located on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 8mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. With regard to operating temperature, this op amp functions well at -40°C~125°C. It is possible to operate this buffer amplifier from a supply current of 2.5mA . You should keep the voltage gain at 124dB for the time being. Op amp ic has 2 channels. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages.
MCP632-E/MF Features
8 Pins
supply voltage of 2.5V
124dB voltage gain
Output Type: Rail-to-Rail
MCP632-E/MF Applications
There are a lot of Microchip Technology MCP632-E/MF Instrumentational OP Amps applications.
- Ultrasound transducers
- Proportional operation circuits
- Fast A/D and D/A converters
- Oscilloscopes
- Thermocouples
- Addition operation circuits
- Band-stop filter
- Displayers for aircraft and air transportation control systems
- Precision measurement
- Signal amplification
