MCP633T-E/SN
| Parameters | |
|---|---|
| Wideband | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP633 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Power Supplies | 3/5V |
| Number of Circuits | 1 |
| Nominal Supply Current | 2.5mA |
| Output Current | 70mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 63 dB |
| Current - Input Bias | 4pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 8mV |
| Gain Bandwidth Product | 24MHz |
| Unity Gain BW-Nom | 24000 kHz |
| Voltage Gain | 124dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Voltage - Input Offset | 1.8mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
MCP633T-E/SN Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. The instrumentation amplifier in this picture is of the General Purpose-type. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are attached to buffer op amp. Please take in mind that op amp should be run at 2.5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are available on the instrumentation amplifier. With regard to input offset voltage, instrumentation amplifier is rated at 8mV. The mounting type that is recommended for this electrical part is Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureVoltage gain should remain at 124dB. This op amp contains 1 circuits. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. There is a rating of 1 for the operating supply voltage of the buffer op amp. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
MCP633T-E/SN Features
8 Pins
supply voltage of 2.5V
124dB voltage gain
Output Type: Rail-to-Rail
MCP633T-E/SN Applications
There are a lot of Microchip Technology MCP633T-E/SN Instrumentational OP Amps applications.
- Mobile phone
- Cinema or auditorium audio system
- Micro signal measurement
- Communication device
- MP3
- Non-polarized electrodes
- Video amplifiers
- Radiation thermometry transducers
- Video data acquisition
- Test and measurement instruments
