MCP634-E/ST
| Parameters | |
|---|---|
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP634 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Number of Circuits | 4 |
| Nominal Supply Current | 2.5mA |
| Output Current | 70mA |
| Slew Rate | 10V/μs |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 63 dB |
| Current - Input Bias | 4pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 8mV |
| Gain Bandwidth Product | 24MHz |
| Unity Gain BW-Nom | 24000 kHz |
| Voltage Gain | 124dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Supply Voltage Limit-Max | 6.5V |
| Voltage - Input Offset | 1.8mV |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
MCP634-E/ST Overview
It is packaged in an 14-TSSOP (0.173, 4.40mm Width)-case that protects the operational amplifiers from damage. A General Purpose-type buffer amplifier is shown here. A Tube case is used for delivering the op amp. A total of 14 terminations have been reported in the past few weeks. In total, there are 14 pins on this op amp ic. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 2.5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. The buffer op amp includes 14 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 8mV. For this electrical component, Surface Mount is the recommended mounting type. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Keeping the voltage gain at 124dB is the best course of action. During the manufacturing process, this buffer amplifier is divided into 4 circuits. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The total number of elements in this buffer amplifier is 4.
MCP634-E/ST Features
14 Pins
supply voltage of 2.5V
124dB voltage gain
Output Type: Rail-to-Rail
MCP634-E/ST Applications
There are a lot of Microchip Technology MCP634-E/ST Instrumentational OP Amps applications.
- High gain DC amplifier
- Communication
- High input resistance broadband
- Blood pressure sensors
- Multiplication circuits
- Large motor controllers
- Micro signal measurement
- Test and measurement instruments
- Switching amplifier
- Radar
