banner_page

MCP635-E/MF

2 Channels 4pA 63 dB Instrumentational OP Amps 0.005μA 2.5V~5.5V MCP635 10 Pins 10-VFDFN Exposed Pad


  • Manufacturer: Microchip Technology
  • Nocochips NO: 536-MCP635-E/MF
  • Package: 10-VFDFN Exposed Pad
  • Datasheet: PDF
  • Stock: 960
  • Description: 2 Channels 4pA 63 dB Instrumentational OP Amps 0.005μA 2.5V~5.5V MCP635 10 Pins 10-VFDFN Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 10-VFDFN Exposed Pad
Number of Pins 10
Operating Temperature -40°C~125°C
Packaging Tube
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 10
ECCN Code EAR99
Terminal Finish Matte Tin (Sn) - annealed
Subcategory Operational Amplifier
Technology CMOS
Terminal Position DUAL
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 2.5V
Terminal Pitch 0.5mm
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number MCP635
Pin Count 10
Output Type Rail-to-Rail
Power Supplies 3/5V
Number of Channels 2
Number of Circuits 2
Nominal Supply Current 2.5mA
Output Current 70mA
Slew Rate 10V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 63 dB
Current - Input Bias 4pA
Voltage - Supply, Single/Dual (±) 2.5V~5.5V
Input Offset Voltage (Vos) 8mV
Bandwidth 24MHz
Unity Gain BW-Nom 24000 kHz
Voltage Gain 124dB
Average Bias Current-Max (IIB) 0.005μA
Power Supply Rejection Ratio (PSRR) 61dB
Low-Offset NO
Frequency Compensation YES
Supply Voltage Limit-Max 6.5V
Voltage - Input Offset 1.8mV
Low-Bias YES
Micropower NO
Max Frequency 1MHz
Programmable Power NO
Height 950μm
Length 3mm
Width 3mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

MCP635-E/MF Overview


In order to protect the op amps, a 10-VFDFN Exposed Pad case is used. There are two types of operational amplifiers in this circuit. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. There have been a total of 10 terminations over the past year. In total, there are 10 pins on this op amp ic. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 2.5V. It should be noted that this op amp is a type of Operational Amplifier device. 10 pins are located on the operational amplifiers. Regarding input offset voltage, buffer amplifier rates 8mV voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperature124dB should be the voltage gain. The buffer amp consists of 2 circuits in total. There are 2 channels on the operational amplifiers. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals.

MCP635-E/MF Features


10 Pins
supply voltage of 2.5V
124dB voltage gain
Output Type: Rail-to-Rail

MCP635-E/MF Applications


There are a lot of Microchip Technology MCP635-E/MF Instrumentational OP Amps applications.

  • Subtraction operation circuits
  • High input resistance broadband
  • Biopotential
  • Multiplication circuits
  • Automotive sensors
  • Proportional operation circuits
  • Video computer boards
  • Tablets
  • Micro signal measurement
  • Fission chambers

Write a review

Note: HTML is not translated!
    Bad           Good