MCP6401RT-E/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6401R |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Nominal Supply Current | 45μA |
| Output Current | 15mA |
| Current - Supply | 45μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 56 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 63dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6401RT-E/OT Overview
Packaging for the buffer amplifier is in the form of a SC-74A, SOT-753 case. An op amp of this type is a General Purpose-type. The op amp is delivered to you in a Tape & Reel (TR) case. The number of terminations approaches 5. The pins on this board total to 5 in total. It would be helpful if you could remember that this op amp ic should be powered by an 1.8V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. A total of 5 pins are present on the instrumentation amplifier. Op amp ic rates 4.5mV for input offset voltage. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . Voltage gain should remain at 110dB. There are 1 channels on the operational amplifiers. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. An buffer amplifier is packed in a TAPE AND REEL-shape according to the design. To run supply current of buffer amplifier under 45μA.
MCP6401RT-E/OT Features
5 Pins
supply voltage of 1.8V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6401RT-E/OT Applications
There are a lot of Microchip Technology MCP6401RT-E/OT Instrumentational OP Amps applications.
- Switching amplifier
- Communication device
- Broadcasting
- Industrial applications including automation
- Video conversion and routing
- Signal operation
- Integrator circuits
- Cinema or auditorium audio system
- Active probe
- Measurements of Wheatstone bridge
