MCP6402T-E/MNY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6402 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Nominal Supply Current | 45μA |
| Output Current | 15mA |
| Current - Supply | 45μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 56 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 63dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Height | 762μm |
| Length | 1.9812mm |
| Width | 2.9972mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6402T-E/MNY Overview
There is a 8-WFDFN Exposed Pad case in which the instrumentation amplifier is packaged. General Purpose-type instrumentation amplifiers are used in this application. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 1.8V. Instrumentation amplifier is a part of Operational Amplifier. The op amp ic has an array of 8 pins on it. Op amp rates 4.5mV as input offset voltage. This electrical part should be mounted using type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . It is a member of the 110dB's 110dB family. There are a total of 2 channels available on the op amps. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. We recommend that you use this electronic part with an 45μA supply in order to get the best performance from it.
MCP6402T-E/MNY Features
8 Pins
supply voltage of 1.8V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6402T-E/MNY Applications
There are a lot of Microchip Technology MCP6402T-E/MNY Instrumentational OP Amps applications.
- Band-stop filter
- Voltage regulation circuit
- Power control
- Tablets
- Proportional counter tubes
- Power generator
- Fission chambers
- Radiation thermometry transducers
- Division circuits
- earphone
