MCP6404-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6404 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Channels | 4 |
| Nominal Supply Current | 45μA |
| Output Current | 15mA |
| Current - Supply | 45μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 56 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 63dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Height | 1.05mm |
| Length | 5.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6404-E/ST Overview
The linear amplifier is packaged in a 14-TSSOP (0.173, 4.40mm Width) case which makes it easy for the consumer to handle. The instrumentation amplifier in this picture is of the General Purpose-type. A Tube case is used to deliver the buffer op amp. During the past two weeks, there have been close to 14 terminations. Buffer amplifier has a total of 14 pins. Please take in mind that op amp should be run at 1.8V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. In total, the buffer amplifier consists of 14 pins. The input offset voltage is 4.5mV. Surface Mount is the recommended mounting type for this linear amplifier. With regard to operating temperature, this op amp functions well at -40°C~125°C. Maintain 110dB as the voltage gain. On the buffer amps, there are 4 channels that can be used. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. As a recommendation, this electronic component should be used with a power supply that can deliver 45μA.
MCP6404-E/ST Features
14 Pins
supply voltage of 1.8V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6404-E/ST Applications
There are a lot of Microchip Technology MCP6404-E/ST Instrumentational OP Amps applications.
- Power transmission
- Band-stop filter
- Automation control systems
- ECG equipment
- Proportional operation circuits
- Image computer boards
- Portable media players
- Measurements of Wheatstone bridge
- Voltage regulation circuit
- Signal amplification
