MCP6404T-E/SL
| Parameters | |
|---|---|
| Number of Functions | 4 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6404 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 2/5V |
| Nominal Supply Current | 45μA |
| Output Current | 15mA |
| Current - Supply | 45μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 56 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Gain Bandwidth Product | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 63dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
MCP6404T-E/SL Overview
In the package, you will find a 14-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. Buffer amps of this type are called General Purpose-types. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. A total of 14 terminations have been reported in the past few weeks. The total number of pins on linear amplifier is 14. The linear amplifier should be run at 1.8V at all times, so please keep that in mind when using it. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. The op amp ic has an array of 14 pins on it. Regarding input offset voltage, op amp rates 4.5mV. This electronic part is recommended for mounting type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . It is recommended to keep the voltage gain at 110dB at all times. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. For the operating supply voltage of the op amp ic, there is a rating of 4. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. We recommend that you use this electronic part with an 45μA supply in order to get the best performance from it.
MCP6404T-E/SL Features
14 Pins
supply voltage of 1.8V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6404T-E/SL Applications
There are a lot of Microchip Technology MCP6404T-E/SL Instrumentational OP Amps applications.
- Commercial audio systems
- Medical instruments
- Power transmission
- Video conversion and routing
- Multiplication circuits
- Signal operation
- Test and measurement instruments
- Addition operation circuits
- Displayers for aircraft and air transportation control systems
- Test equipment
