MCP6404T-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6404 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 2/5V |
| Nominal Supply Current | 45μA |
| Output Current | 15mA |
| Current - Supply | 45μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 56 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Gain Bandwidth Product | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 63dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6404T-E/ST Overview
In order to protect the op amps, a 14-TSSOP (0.173, 4.40mm Width) case is used. An op amp ic of the General Purpose type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. We are approaching the 14h termination of the year. A total of 14 pins are located on this board. Please take in mind that op amp should be run at 1.8V. Instrumentation amplifier is a part of Operational Amplifier. In total, the buffer amplifier consists of 14 pins. With regard to input offset voltage, instrumentation amplifier is rated at 4.5mV. Surface Mount is the recommended mounting type of operational amplifiers. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. There should be no change in the voltage gain at 110dB. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. A voltage rating of 4 is indicated for the op amp's operating supply voltage. TAPE AND REEL is adopted to pack the instrumentation amplifier. It is recommended that this electronic component be used with an 45μA supply.
MCP6404T-E/ST Features
14 Pins
supply voltage of 1.8V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6404T-E/ST Applications
There are a lot of Microchip Technology MCP6404T-E/ST Instrumentational OP Amps applications.
- RF cable systems
- Biopotential
- Medical imaging
- Band-stop filter
- Exponential operation circuits
- Voltage regulation circuit
- Video conversion and routing
- High speed sample
- Portable electronic products powered by batteries
- Medical instruments
