MCP6407-H/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~150°C |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6407 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Operating Supply Current | 45μA |
| Nominal Supply Current | 45μA |
| Output Current | 15mA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 56 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 15mA |
| Input Offset Voltage (Vos) | 4.5mV |
| Gain Bandwidth Product | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 63dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MCP6407-H/SN Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. An op amp ic of the General Purpose type. There is a Tube case that is delivered with the instrumentation amplifiers. There is a growing number of terminations approaching the number of 8. A total of 8 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 1.8V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are available on the instrumentation amplifier. Op amp ic rates 4.5mV for input offset voltage. This electronic part is best mounted with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~150°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 45μA and 10 . It is recommended to keep the voltage gain at 110dB at all times. On the output type, there are Rail-to-Rail different types of op amps. The op amp is rated for an operating supply voltage of 2.
MCP6407-H/SN Features
8 Pins
supply voltage of 1.8V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6407-H/SN Applications
There are a lot of Microchip Technology MCP6407-H/SN Instrumentational OP Amps applications.
- Video conversion and routing
- Signal operation
- Test and measurement instruments
- Logarithmic operation circuits
- Non-polarized electrodes
- Precision measurement
- Vehicle electronics
- RF cable systems
- Instrumentation
- Displayers for aircraft and air transportation control systems
