MCP6441T-E/LT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6441 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Nominal Supply Current | 450nA |
| Output Current | 22mA |
| Current - Supply | 450nA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 9 kHz |
| Unity Gain BW-Nom | 9000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 65dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1mm |
| Length | 2.25mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6441T-E/LT Overview
The linear amplifier is packaged in a 5-TSSOP, SC-70-5, SOT-353 case. Op amps are General Purpose types of amplifier on the chip. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. In recent months, the number of terminations has approached 5. It consists of a total of 5 pins in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The buffer op amp includes 5 pins. There is an input offset voltage of 4.5mV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureYou should keep the voltage gain at 110dB for the time being. Op amp ic has 1 channels. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. In order to ensure optimal performance, an 450nA supply is recommended for this electrical component.
MCP6441T-E/LT Features
5 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6441T-E/LT Applications
There are a lot of Microchip Technology MCP6441T-E/LT Instrumentational OP Amps applications.
- Signal transformation
- Video amplifiers
- Semiconductor detectors
- Instrumentation
- Image computer boards
- single/dual op amp sum and difference circuits
- Large motor controllers
- Vehicle electronics
- Thermocouples
- Broadcasting
