MCP6441T-E/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6441 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Nominal Supply Current | 450nA |
| Output Current | 22mA |
| Current - Supply | 450nA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 9 kHz |
| Unity Gain BW-Nom | 9000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 65dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.2954mm |
| Length | 3.0988mm |
| Width | 1.8034mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6441T-E/OT Overview
In order to protect the op amps, a SC-74A, SOT-753 case is used. General Purpose-type instrumentation amplifiers are used in this application. The op amp is delivered to you in a Tape & Reel (TR) case. A total of 5 terminations have been reported in the past few weeks. Buffer amplifier has a total of 5 pins on it. Please take in mind that this instrumentation amplifier should be run at 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. It has 5 pins that make up the linear amplifier. There is an input offset voltage of 4.5mV for this buffer op amp. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureMaintain 110dB as the voltage gain. There are 1 channels on the operational amplifiers. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted. We recommend that you use this electronic part with an 450nA supply in order to get the best performance from it.
MCP6441T-E/OT Features
5 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6441T-E/OT Applications
There are a lot of Microchip Technology MCP6441T-E/OT Instrumentational OP Amps applications.
- Voltage regulation circuit
- Digital cameras
- Vehicle electronics
- Signal operation
- Proportional counter tubes
- Television
- Strain gauges
- Instrumentation
- Video data acquisition
- Portable media players
