MCP6444-E/SL
| Parameters | |
|---|---|
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6444 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 1.5/5V |
| Number of Channels | 4 |
| Operating Supply Current | 450nA |
| Nominal Supply Current | 450nA |
| Output Current | 22mA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Output Current per Channel | 22mA |
| Input Offset Voltage (Vos) | 4.5mV |
| Bandwidth | 9 kHz |
| Unity Gain BW-Nom | 9000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 65dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Height | 1.2446mm |
| Length | 8.636mm |
| Width | 3.9116mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
MCP6444-E/SL Overview
It is packaged in an 14-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. There are two types of operational amplifiers in this circuit. Instrumentation amplifier is delivered in a Tube case. It is estimated that there will be 14 terminations in the next few months. In total, there are 14 pins on this op amp ic. This linear amplifier should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. An 14-pin op amp ic is included in the package. Op amp rates 4.5mV as input offset voltage. It is recommended that this electronic component be mounted using the Surface Mount mounting type. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. An 450nA volt supply current is needed for this linear amplifier to operate. 110dB should be the voltage gain. 4 channels are available on the instrumentation amplifier. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages.
MCP6444-E/SL Features
14 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6444-E/SL Applications
There are a lot of Microchip Technology MCP6444-E/SL Instrumentational OP Amps applications.
- Car stereo
- Active probe
- Voltage regulation circuit
- Cinema or auditorium audio system
- Signal amplification
- Tablets
- Image computer boards
- Addition operation circuits
- Vehicle electronics
- Broadcasting
