MCP6481T-E/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6481 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Nominal Supply Current | 240μA |
| Slew Rate | 2.7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.2V~5.5V ±1.1V~2.25V |
| Input Offset Voltage (Vos) | -1.5mV |
| Bandwidth | 4MHz |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 91dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.5mV |
| Current - Output / Channel | 12mA |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 10kHz |
| Programmable Power | NO |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6481T-E/OT Overview
Packaged in a SC-74A, SOT-753 case, the buffer op amp is ready to use. The instrumentation amplifier in this picture is of the General Purpose-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. The number of terminations approaches 5. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. In total, the buffer amplifier consists of 5 pins. The input offset voltage is -1.5mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. Op amp is a member of the 115dB's 115dB family. A linear amplifier like this has 1 circuits on it. Buffer op amp is equipped with 1 channels on the device. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The linear amplifier is packaged by using a TAPE AND REEL axis.
MCP6481T-E/OT Features
supply voltage of 3V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6481T-E/OT Applications
There are a lot of Microchip Technology MCP6481T-E/OT Instrumentational OP Amps applications.
- Signal filtering
- Blood pressure sensors
- Broadcasting
- Exponential operation circuits
- Video data acquisition
- Semiconductor detectors
- Radar
- Information processing
- Displayers for aircraft and air transportation control systems
- Portable media players
