MCP651ST-E/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2017 |
| Series | mCal Technology |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP651 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Nominal Supply Current | 6mA |
| Output Current | 95mA |
| Current - Supply | 6mA |
| Slew Rate | 30V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 6pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 50MHz |
| Unity Gain BW-Nom | 50000 kHz |
| Voltage Gain | 123dB |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Current - Output / Channel | 100mA |
| Low-Bias | YES |
| Height | 1.2954mm |
| Length | 3.0988mm |
| Width | 1.8034mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP651ST-E/OT Overview
A SC-74A, SOT-753 case is used to package the op amp. An op amp ic of the General Purpose type. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. The number of terminations approaches 5. The total number of pins on linear amplifier is 5. Please take in mind that this instrumentation amplifier should be run at 2.5V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. A total of 5 pins are present on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 200μV. For this electrical component, Surface Mount is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. There should be no change in the voltage gain at 123dB. 1 channels are available on the instrumentation amplifier. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. As a result of this, the buffer amplifier is packed in TAPE AND REEL. This electronic part is recommended to be used with an 6mA supply for best performance. The mCal Technology stands for the buffer op amp's serial number.
MCP651ST-E/OT Features
5 Pins
supply voltage of 2.5V
123dB voltage gain
Output Type: Rail-to-Rail
MCP651ST-E/OT Applications
There are a lot of Microchip Technology MCP651ST-E/OT Instrumentational OP Amps applications.
- Medical instruments
- Tablets
- Inverse/same-phase proportional circuit
- Fast A/D and D/A converters
- Radar
- Division circuits
- RF cable systems
- Automotive sensors
- Communication
- Vehicle electronics
