MCP652T-E/SN
| Parameters | |
|---|---|
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP652 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Operating Supply Current | 6mA |
| Nominal Supply Current | 6mA |
| Output Current | 95mA |
| Slew Rate | 30V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 6pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 200μV |
| Gain Bandwidth Product | 50MHz |
| Unity Gain BW-Nom | 50000 kHz |
| Voltage Gain | 123dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| Series | mCal Technology |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
MCP652T-E/SN Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. An op amp ic of the General Purpose type. The op amp is delivered to you in a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. Linear amplifier has a total of 8 pins. Please take in mind that this instrumentation amplifier should be run at 2.5V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are included on the operational amplifiers. Op amp rates 200μV as input offset voltage. This electronic part is recommended for mounting type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . A supply current of 6mA can be used to operate this linear amplifier. 123dB should be the voltage gain. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. There is an operating supply voltage rating of 2 for this operational amplifier, which is rated at the manufacturer. This linear amplifier pack is based on the TAPE AND REEL axis. Buffer op amp series numbers are indicated by the mCal Technology.
MCP652T-E/SN Features
8 Pins
supply voltage of 2.5V
123dB voltage gain
Output Type: Rail-to-Rail
MCP652T-E/SN Applications
There are a lot of Microchip Technology MCP652T-E/SN Instrumentational OP Amps applications.
- Video conversion and routing
- Signal transformation
- Television
- Biopotential
- Navigation
- Signal filtering
- Mobile phone
- Proportional counter tubes
- Commercial audio systems
- Laptop
