MCP6544-I/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Supplier Device Package | 14-PDIP |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2007 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | General Purpose |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Base Part Number | MCP6544 |
| Output Type | CMOS, Push-Pull, Rail-to-Rail, TTL |
| Number of Elements | 4 |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.6V |
| Nominal Supply Current | 1mA |
| Output Current | 2mA |
| Max Supply Current | 1mA |
| Propagation Delay | 8 μs |
| Quiescent Current | 1μA |
| Response Time | 4 μs |
| Common Mode Rejection Ratio | 70 dB |
| Voltage - Supply, Single/Dual (±) | 1.6V~5.5V |
| Output Current per Channel | 2mA |
| Input Offset Voltage (Vos) | 7mV |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Max Input Current | 1pA |
| Input Bias Current | 1pA |
| Current - Quiescent (Max) | 1μA |
| Voltage - Input Offset (Max) | 7mV @ 5.5V |
| Current - Input Bias (Max) | 1pA @ 5.5V |
| Hysteresis | 6.5mV |
| CMRR, PSRR (Typ) | 70dB CMRR, 80dB PSRR |
| Natural Thermal Resistance | 70 °C/W |
| Propagation Delay (Max) | 8μs |
| Height | 3.3mm |
| Length | 19.05mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6544-I/P Overview
A convenient transport package is provided in 14-DIP (0.300, 7.62mm) .A comparator with a CMOS, Push-Pull, Rail-to-Rail, TTL output is used here.Electronic comparator is shipped by Tube .The type of the chip can be classified as General Purpose .There are a total of 4 elements in it.Electronic comparator is recommended to mount the device using type Through Hole .If you want to avoid malfunction, you should set the operating temperature to -40°C~85°C .The comparator has 14 pins.Try search MCP6544 to get more pin-to-pin solutions for your special needs.There is a quiescent current of 1μA in this comparator.There is a Through Hole for mounting it on a PCB or other board.Normally, the nominal supply current should be 1mA .The compartator could be damaged if the current supply exceeds 1mA .Input current to the device cannot exceed 1pA .Comparator electronics is not recommended to operate at a temperature higher than 85°C .Temperature lower than -40°C is not suitable for the it.Comparator electronics is specified that the comparator's maximum supply voltage is 5.5V .A minimum supply voltage of 1.6V is allowed for this comparator.For the output quality to be maintained, 4 channels work together.
MCP6544-I/P Features
CMOS, Push-Pull, Rail-to-Rail, TTL output capability
General Purpose IC
Employing 4 elements
Operates under -40°C~85°C
Quiescent Current: 1μA
MCP6544-I/P Applications
There are a lot of Microchip Technology MCP6544-I/P linear comparators applications.
- Simple Analog-to-Digital Converters (ADCs)
- Point of load regulators
- Ultra-Low Power Systems
- Hand-Held Electronics
- Motor drives
- Consumer Medical Electronics
- Power Supervision
- Automatic Test Equipment
- Portable and Battery-Powered Systems
- Zero-Crossing Detectors
