MCP655-E/MF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2008 |
| Series | mCal Technology |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP655 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Operating Supply Current | 6mA |
| Nominal Supply Current | 6mA |
| Output Current | 95mA |
| Slew Rate | 30V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 6pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 50MHz |
| Unity Gain BW-Nom | 50000 kHz |
| Voltage Gain | 123dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | NO |
| Max Frequency | 1MHz |
| Programmable Power | NO |
| Height | 950μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP655-E/MF Overview
In the package, you will find a 10-VFDFN Exposed Pad-case to contain the op amp ic. Op amps are General Purpose types of amplifier on the chip. There is a Tube case that is delivered with the instrumentation amplifiers. During the past two weeks, there have been close to 10 terminations. It consists of a total of 10 pins in total. It is important to remember that this op amp should be operated at a voltage of 2.5V volts. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 10 pins are included on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 200μV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . A supply current of 6mA can be used to operate this linear amplifier. There should be no change in the voltage gain. Buffer op amp is equipped with 2 channels on the device. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. This buffer amplifier is assigned within the mCal Technology series by its manufacturer.
MCP655-E/MF Features
10 Pins
supply voltage of 2.5V
123dB voltage gain
Output Type: Rail-to-Rail
MCP655-E/MF Applications
There are a lot of Microchip Technology MCP655-E/MF Instrumentational OP Amps applications.
- Cinema or auditorium audio system
- Measurements of Wheatstone bridge
- Power control
- Radar
- Fast A/D and D/A converters
- E-book readers
- Television broadcasting equipment
- Exponential operation circuits
- Video conversion and routing
- Automatic control
