MCP655T-E/MF
| Parameters | |
|---|---|
| Base Part Number | MCP655 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Nominal Supply Current | 6mA |
| Output Current | 95mA |
| Current - Supply | 6mA |
| Slew Rate | 30V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 6pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 200μV |
| Gain Bandwidth Product | 50MHz |
| Unity Gain BW-Nom | 50000 kHz |
| Voltage Gain | 123dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Current - Output / Channel | 100mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | mCal Technology |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
MCP655T-E/MF Overview
In order to protect the op amps, a 10-VFDFN Exposed Pad case is used. A General Purpose-type buffer amplifier is shown here. A Tape & Reel (TR) case is used for delivering the op amp. There is a growing number of terminations approaching the number of 10. The total number of pins on linear amplifier is 10. I would like to remind you that this buffer op amp should be powered by an 2.5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. An 10-pin op amp ic is included in the package. Op amp ic rates 200μV for input offset voltage. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . Maintain 123dB as the voltage gain. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. As a whole, there are 2 elements that make up this buffer amplifier. An buffer amplifier is packed in a TAPE AND REEL-shape according to the design. This electronic part is recommended to be used with an 6mA supply for best performance. mCal Technology corresponds to linear amplifier's series.
MCP655T-E/MF Features
10 Pins
supply voltage of 2.5V
123dB voltage gain
Output Type: Rail-to-Rail
MCP655T-E/MF Applications
There are a lot of Microchip Technology MCP655T-E/MF Instrumentational OP Amps applications.
- Laptop
- Signal filtering
- single/dual op amp sum and difference circuits
- Subtraction operation circuits
- Mobile phone
- Biopotential
- Test and measurement instruments
- Proportional counter tubes
- Video conversion and routing
- Power control
