MCP655T-E/UN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| Series | mCal Technology |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP655 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Nominal Supply Current | 6mA |
| Output Current | 95mA |
| Current - Supply | 6mA |
| Slew Rate | 30V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 6pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 200μV |
| Gain Bandwidth Product | 50MHz |
| Unity Gain BW-Nom | 50000 kHz |
| Voltage Gain | 123dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Current - Output / Channel | 100mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MCP655T-E/UN Overview
There is a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) case package that contains the instrumentation amplifiers. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Tape & Reel (TR) case. The number of terminations approaches 10. Linear amplifier has a total of 10 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 2.5V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. Linear amplifier includes 10 pins. As far as the input offset voltage is concerned, linear amplifier rates at 200μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. There should be no change in the voltage gain at 123dB. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. As a whole, there are 2 elements that make up this buffer amplifier. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. It is recommended that you use an 6mA power supply with this electrical part in order for it to operate correctly. mCal Technology corresponds to the op amp's series.
MCP655T-E/UN Features
10 Pins
supply voltage of 2.5V
123dB voltage gain
Output Type: Rail-to-Rail
MCP655T-E/UN Applications
There are a lot of Microchip Technology MCP655T-E/UN Instrumentational OP Amps applications.
- Image computer boards
- Power control
- Medical instruments
- High-frequency data acquisition systems
- Multiplication circuits
- Test and measurement instruments
- Power generator
- Band-stop filter
- Communication
- Home audio systems
