banner_page

MCP660-E/ST

3 Channels 80mA per Channel 6pA 64 dB Instrumentational OP Amps 0.005μA 2.5V~5.5V ±1.25V~2.75V MCP660 14 Pins 14-TSSOP (0.173, 4.40mm Width)


  • Manufacturer: Microchip Technology
  • Nocochips NO: 536-MCP660-E/ST
  • Package: 14-TSSOP (0.173, 4.40mm Width)
  • Datasheet: PDF
  • Stock: 363
  • Description: 3 Channels 80mA per Channel 6pA 64 dB Instrumentational OP Amps 0.005μA 2.5V~5.5V ±1.25V~2.75V MCP660 14 Pins 14-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 14-TSSOP (0.173, 4.40mm Width)
Number of Pins 14
Operating Temperature -40°C~125°C
Packaging Tube
Published 2011
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
ECCN Code EAR99
Terminal Finish Matte Tin (Sn) - annealed
Subcategory Operational Amplifier
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 3
Supply Voltage 2.5V
Terminal Pitch 0.65mm
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number MCP660
Pin Count 14
Output Type Rail-to-Rail
Number of Channels 3
Operating Supply Current 6mA
Nominal Supply Current 6mA
Output Current 90mA
Slew Rate 32V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 64 dB
Current - Input Bias 6pA
Voltage - Supply, Single/Dual (±) 2.5V~5.5V ±1.25V~2.75V
Output Current per Channel 80mA
Input Offset Voltage (Vos) 1.8mV
Bandwidth 60MHz
Unity Gain BW-Nom 60000 kHz
Voltage Gain 126dB
Average Bias Current-Max (IIB) 0.005μA
Power Supply Rejection Ratio (PSRR) 61dB
Low-Offset NO
Frequency Compensation YES
Supply Voltage Limit-Max 6.5V
Low-Bias YES
Micropower NO
Programmable Power NO
Height 1.05mm
Length 5.1mm
Width 4.5mm

MCP660-E/ST Overview


In the package, you will find a 14-TSSOP (0.173, 4.40mm Width)-case to contain the op amp ic. Buffer amps of this type are called General Purpose-types. Linear amplifier is delivered in a Tube case. The number of terminations is approaching the 14 mark. It consists of a total of 14 pins in total. It is important to remember that this op amp should be operated at a voltage of 2.5V volts. Instrumentation amplifier is a part of Operational Amplifier. It has 14 pins that make up the linear amplifier. Regarding input offset voltage, op amp rates 1.8mV. The mounting type that is recommended for this electrical part is Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. A supply current of 6mA can be used to operate this linear amplifier. It is a member of the 126dB's 126dB family. As far as the device is concerned, buffer amplifier has 3 channels. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals.

MCP660-E/ST Features


14 Pins
supply voltage of 2.5V
126dB voltage gain
Output Type: Rail-to-Rail

MCP660-E/ST Applications


There are a lot of Microchip Technology MCP660-E/ST Instrumentational OP Amps applications.

  • Digital cameras
  • Multimedia playback equipment
  • Commercial audio systems
  • Hand-held batteries
  • Mobile phone
  • Non-polarized electrodes
  • Weak signal detection
  • Broadcasting
  • Logarithmic operation circuits
  • Inverse/same-phase proportional circuit

Write a review

Note: HTML is not translated!
    Bad           Good