banner_page

MCP660T-E/SL

6pA 66 dB Instrumentational OP Amps 0.005μA 2.5V~5.5V ±1.25V~2.75V MCP660 14 Pins 14-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Microchip Technology
  • Nocochips NO: 536-MCP660T-E/SL
  • Package: 14-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 607
  • Description: 6pA 66 dB Instrumentational OP Amps 0.005μA 2.5V~5.5V ±1.25V~2.75V MCP660 14 Pins 14-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 14-SOIC (0.154, 3.90mm Width)
Number of Pins 14
Operating Temperature -40°C~125°C
Packaging Tape & Reel (TR)
Published 2012
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
ECCN Code EAR99
Terminal Finish Matte Tin (Sn) - annealed
Subcategory Operational Amplifier
Packing Method TAPE AND REEL
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 3
Supply Voltage 2.5V
Terminal Pitch 1.27mm
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number MCP660
Pin Count 14
Qualification Status Not Qualified
Output Type Rail-to-Rail
Number of Elements 3
Number of Circuits 3
Nominal Supply Current 6mA
Output Current 90mA
Slew Rate 32V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 66 dB
Current - Input Bias 6pA
Voltage - Supply, Single/Dual (±) 2.5V~5.5V ±1.25V~2.75V
Input Offset Voltage (Vos) 8mV
Gain Bandwidth Product 60MHz
Unity Gain BW-Nom 60000 kHz
Voltage Gain 126dB
Average Bias Current-Max (IIB) 0.005μA
Power Supply Rejection Ratio (PSRR) 61dB
Low-Offset NO
Frequency Compensation YES
Supply Voltage Limit-Max 6.5V
Voltage - Input Offset 1.8mV
Low-Bias YES
Micropower NO
Programmable Power NO
Wideband NO
Height Seated (Max) 1.75mm
Length 8.65mm
RoHS Status ROHS3 Compliant

MCP660T-E/SL Overview


There is a 14-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. An op amp ic of the General Purpose type. A Tape & Reel (TR) case is used for delivering the op amp. It is estimated that there will be 14 terminations in the next few months. Buffer amplifier has a total of 14 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 2.5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The buffer op amp includes 14 pins. In terms of the input offset voltage, instrumentation amplifier rates at 8mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureThe voltage gain should stay at 126dB. A linear amplifier like this has 3 circuits on it. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. There are 3 elements in total in this linear amplifier. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.

MCP660T-E/SL Features


14 Pins
supply voltage of 2.5V
126dB voltage gain
Output Type: Rail-to-Rail

MCP660T-E/SL Applications


There are a lot of Microchip Technology MCP660T-E/SL Instrumentational OP Amps applications.

  • Signal amplification
  • Scintillation detectors
  • RF cable systems
  • Portable media players
  • Inverse/same-phase proportional circuit
  • Fast A/D and D/A converters
  • Signal filtering
  • Automotive sensors
  • Measurements of Wheatstone bridge
  • Integrator circuits

Write a review

Note: HTML is not translated!
    Bad           Good