MCP664T-E/SL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP664 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 3/5V |
| Number of Circuits | 4 |
| Nominal Supply Current | 6mA |
| Output Current | 90mA |
| Slew Rate | 32V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 6pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V ±1.25V~2.75V |
| Input Offset Voltage (Vos) | 8mV |
| Gain Bandwidth Product | 60MHz |
| Unity Gain BW-Nom | 60000 kHz |
| Voltage Gain | 126dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Voltage - Input Offset | 1.8mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| RoHS Status | ROHS3 Compliant |
MCP664T-E/SL Overview
A 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. The number of terminations approaches 14. Buffer amplifier has a total of 14 pins on it. The linear amplifier should be run at 2.5V at all times, so please keep that in mind when using it. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 14 pins are included on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 8mV. For this electronic part, it is recommended that you mount it with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. There should be no change in the voltage gain. This op amp ic has 4 circuits. On the output type, there are Rail-to-Rail different types of op amps. For the operating supply voltage of the op amp ic, there is a rating of 4. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
MCP664T-E/SL Features
14 Pins
supply voltage of 2.5V
126dB voltage gain
Output Type: Rail-to-Rail
MCP664T-E/SL Applications
There are a lot of Microchip Technology MCP664T-E/SL Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Communication device
- Fission chambers
- Broadcasting
- Strain gauges
- Inverse/same-phase proportional circuit
- Band-stop filter
- Proportional operation circuits
- Test and measurement instruments
- Ultrasound transducers
