MCP6G01T-E/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Instrumentation Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6G01 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Operating Supply Current | 110μA |
| Nominal Supply Current | 30mA |
| Slew Rate | 4.5V/μs |
| Amplifier Type | General Purpose |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 4.5mV |
| Voltage Gain | 33.98dB |
| Power Supply Rejection Ratio (PSRR) | 65dB |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| -3db Bandwidth | 900kHz |
| Voltage Gain-Nom | 10 |
| Non-linearity-Max | 0.05% |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6G01T-E/MS Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. The number of terminations is approaching the 8 mark. It consists of a total of 8 pins in total. In more specific terms, this linear amplifier can be categoriInstrumentation Amplifiered as a Instrumentation Amplifier-type device. There are 8 pins on this chip. The input offset voltage is 4.5mV. For this electrical component, Surface Mount is the recommended mounting type. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. An 110μA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain at 33.98dB. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The op amp is rated for an operating supply voltage of 1. The operating supply voltage of the buffer op amp is rated at 5V.
MCP6G01T-E/MS Features
8 Pins
33.98dB voltage gain
Output Type: Rail-to-Rail
MCP6G01T-E/MS Applications
There are a lot of Microchip Technology MCP6G01T-E/MS Instrumentational OP Amps applications.
- Thermocouples
- High gain DC amplifier
- High/low-pass filter circuit
- Semiconductor detectors
- Micro signal measurement
- Measurements of Wheatstone bridge
- MP3
- Commercial audio systems
- Image computer boards
- Multimedia playback equipment
