MCP6H01T-E/MNY
| Parameters | |
|---|---|
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6H01 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Nominal Supply Current | 135μA |
| Output Current | 50mA |
| Slew Rate | 0.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 78 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 3.5V~16V ±1.75V~8V |
| Input Offset Voltage (Vos) | 3.5mV |
| Bandwidth | 1.2MHz |
| Unity Gain BW-Nom | 1200 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.025μA |
| Power Supply Rejection Ratio (PSRR) | 87dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 750μm |
| Length | 2mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
MCP6H01T-E/MNY Overview
In order to protect the op amps, a 8-WFDFN Exposed Pad case is used. An op amp of this type is a General Purpose-type. A Tape & Reel (TR) case is used for delivering the op amp. The number of terminations approaches 8. It consists of a total of 8 pins in total. Please take in mind that this instrumentation amplifier should be run at 5V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. Op amp ic rates 3.5mV for input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . You should keep the voltage gain at 115dB for the time being. A linear amplifier like this has 1 circuits on it. There are a total of 1 channels available on the op amps. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of instrumentation amplifier is rated 8V voltage. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted.
MCP6H01T-E/MNY Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6H01T-E/MNY Applications
There are a lot of Microchip Technology MCP6H01T-E/MNY Instrumentational OP Amps applications.
- Image computer boards
- Video amplifiers
- ECG equipment
- Large motor controllers
- RF cable systems
- Hand-held batteries
- Biopotential
- High/low-pass filter circuit
- Addition operation circuits
- PDA
