MCP6H01T-E/SN
| Parameters | |
|---|---|
| Voltage - Supply, Single/Dual (±) | 3.5V~16V ±1.75V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Gain Bandwidth Product | 1.2MHz |
| Unity Gain BW-Nom | 1200 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.025μA |
| Power Supply Rejection Ratio (PSRR) | 87dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 700μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6H01 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Elements | 1 |
| Operating Supply Current | 135μA |
| Nominal Supply Current | 135μA |
| Output Current | 50mA |
| Slew Rate | 0.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 78 dB |
| Current - Input Bias | 10pA |
MCP6H01T-E/SN Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. This is a General Purpose type op amp. The op amp is delivered to you in a Tape & Reel (TR) case. A total of 8 terminations have been reported in the past few weeks. Linear amplifier has a total of 8 pins. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are included on the operational amplifiers. There is an input offset voltage of 3.5mV for this buffer op amp. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . The buffer amplifier is capable of operating from a supply current of 135μA . Op amp is a member of the 115dB's 115dB family. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. There are 1 elements in this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 8V voltage. It is used TAPE AND REEL to pack the op amps.
MCP6H01T-E/SN Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6H01T-E/SN Applications
There are a lot of Microchip Technology MCP6H01T-E/SN Instrumentational OP Amps applications.
- MP3
- Vehicle electronics
- Gaming industry
- High/low-pass filter circuit
- Laptop
- Navigation
- Power transmission
- Weighing systems
- Inverse/same-phase proportional circuit
- Automation control systems
