banner_page

MCP6H84-E/ST

55mA per Channel 10pA 76 dB Instrumentational OP Amps 3.5V~12V ±1.75V~6V MCP6H84 14-TSSOP (0.173, 4.40mm Width)


  • Manufacturer: Microchip Technology
  • Nocochips NO: 536-MCP6H84-E/ST
  • Package: 14-TSSOP (0.173, 4.40mm Width)
  • Datasheet: PDF
  • Stock: 819
  • Description: 55mA per Channel 10pA 76 dB Instrumentational OP Amps 3.5V~12V ±1.75V~6V MCP6H84 14-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 14-TSSOP (0.173, 4.40mm Width)
Number of Pins 14
Operating Temperature -40°C~125°C
Packaging Tube
Published 2012
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
ECCN Code EAR99
Terminal Finish Matte Tin (Sn) - annealed
Subcategory Operational Amplifier
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 5V
Terminal Pitch 0.65mm
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number MCP6H84
Output Type Rail-to-Rail
Power Supplies +-1.75/+-6/3.5/12V
Number of Circuits 4
Operating Supply Current 700μA
Supply Current-Max 5.2mA
Slew Rate 5V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 76 dB
Current - Input Bias 10pA
Voltage - Supply, Single/Dual (±) 3.5V~12V ±1.75V~6V
Output Current per Channel 55mA
Input Offset Voltage (Vos) 1mV
Gain Bandwidth Product 5.5MHz
Unity Gain BW-Nom 5500 kHz
Voltage Gain 120dB
Power Supply Rejection Ratio (PSRR) 82dB
Low-Offset NO
Frequency Compensation YES
Supply Voltage Limit-Max 13.2V
Low-Bias YES
Micropower NO
Programmable Power NO
Wideband NO
Height Seated (Max) 1.2mm
Length 5mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

MCP6H84-E/ST Overview


In order to protect the op amps, a 14-TSSOP (0.173, 4.40mm Width) case is used. General Purpose-type instrumentation amplifiers are used in this application. In the case of Tube cases, linear amplifier will be delivered. The number of terminations approaches 14. I would like to remind you that this buffer op amp should be powered by an 5V battery. It should be noted that this op amp is a type of Operational Amplifier device. 14 pins are located on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 1mV. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . As long as the supply current of the chip does not exceed 700μA, this op amp ic can operate. There should be no change in the voltage gain at 120dB. In total, there are 4 circuits on this buffer amplifier. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has.

MCP6H84-E/ST Features


supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail

MCP6H84-E/ST Applications


There are a lot of Microchip Technology MCP6H84-E/ST Instrumentational OP Amps applications.

  • Tablets
  • Navigation
  • High speed sample
  • E-book readers
  • RF cable systems
  • Signal filtering
  • Micro signal measurement
  • Signal transformation
  • Integrator circuits
  • ECG equipment

Write a review

Note: HTML is not translated!
    Bad           Good