MCP6H92-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6H92 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Nominal Supply Current | 2mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 3.5V~12V ±1.75V~6V |
| Input Offset Voltage (Vos) | 4V |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 13V |
| Voltage - Input Offset | 1mV |
| Current - Output / Channel | 41mA |
| Low-Bias | YES |
| Micropower | NO |
| Max Frequency | 10kHz |
| Programmable Power | NO |
| Height | 1.5mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6H92-E/SN Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. A General Purpose-type buffer amplifier is shown here. In the case of Tube cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 8. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. It has 8 pins that make up the linear amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 4V. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . You should keep the voltage gain at 115dB for the time being. A linear amplifier like this has 2 circuits on it. Op amp ic has 2 channels. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages.
MCP6H92-E/SN Features
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6H92-E/SN Applications
There are a lot of Microchip Technology MCP6H92-E/SN Instrumentational OP Amps applications.
- Comparator
- High/low-pass filter circuit
- Switching amplifier
- Medical instruments
- Radiation thermometry transducers
- ECG equipment
- Ultrasound transducers
- Wireless base stations
- Oscilloscopes
- Logarithmic operation circuits
