MCP6H94-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6H94 |
| Output Type | Rail-to-Rail |
| Power Supplies | +-1.75/+-6/3.5/12V |
| Number of Channels | 4 |
| Current - Supply | 2mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 3.5V~12V ±1.75V~6V |
| Input Offset Voltage (Vos) | 4V |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 13V |
| Voltage - Input Offset | 1mV |
| Current - Output / Channel | 41mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 1.05mm |
| Length | 5.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6H94-E/ST Overview
It is packaged in an 14-TSSOP (0.173, 4.40mm Width)-case that protects the operational amplifiers from damage. Op amps are General Purpose types of amplifier on the chip. The op amp is delivered to you in a Tube case. There have been a total of 14 terminations over the past year. Please take in mind that op amp should be run at 5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 14 pins are available on the instrumentation amplifier. Regarding input offset voltage, buffer amplifier rates 4V voltage. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureYou should keep the voltage gain at 115dB for the time being. Buffer op amp is equipped with 4 channels on the device. On the output type, there are Rail-to-Rail different types of op amps. To run supply current of buffer amplifier under 2mA.
MCP6H94-E/ST Features
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6H94-E/ST Applications
There are a lot of Microchip Technology MCP6H94-E/ST Instrumentational OP Amps applications.
- Exponential operation circuits
- Signal operation
- ECG equipment
- pH (acidity)
- Signal filtering
- Power transmission
- Fast A/D and D/A converters
- Automotive sensors
- Weak signal detection
- Instrumentation
