MCP6L1T-E/MS
| Parameters | |
|---|---|
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 950μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6L1 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Nominal Supply Current | 200μA |
| Output Current | 20mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 105dB |
| Power Supply Rejection Ratio (PSRR) | 90dB |
MCP6L1T-E/MS Overview
In the package, you will find a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case to contain the op amp ic. General Purpose-type instrumentation amplifiers are used in this application. The op amp is delivered to you in a Tape & Reel (TR) case. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are located on this board. Please take in mind that this instrumentation amplifier should be run at 5V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. An 8-pin op amp ic is included in the package. There is an input offset voltage of 3mV for this buffer op amp. For this electronic part, it is recommended that you mount it with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureIt is recommended to keep the voltage gain at 105dB at all times. There are 1 circuits on this op amp. Instrumentation amplifier has 1 channels on it. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of the buffer op amp is rated at 6V. This linear amplifier pack is based on the TAPE AND REEL axis.
MCP6L1T-E/MS Features
8 Pins
supply voltage of 5V
105dB voltage gain
Output Type: Rail-to-Rail
MCP6L1T-E/MS Applications
There are a lot of Microchip Technology MCP6L1T-E/MS Instrumentational OP Amps applications.
- Addition operation circuits
- Differentiator circuits
- Instrumentation
- RF cable systems
- pH (acidity)
- High input resistance broadband
- Laptop
- Automation control systems
- E-book readers
- Non-polarized electrodes
