MCP6L4T-E/SL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6L4 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Power Supplies | 5V |
| Number of Channels | 4 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 200μA |
| Output Current | 20mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 105dB |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Height | 1.25mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6L4T-E/SL Overview
A 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. Op amps are General Purpose types of amplifier on the chip. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. It is estimated that there will be 14 terminations in the next few months. The total number of pins on linear amplifier is 14. This linear amplifier should be powered by an 5V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. An 14-pin op amp ic is included in the package. The input offset voltage is 3mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Using a supply current of 200μA , this buffer op amp will be able to operate. 105dB should remain the voltage gain. Instrumentation amplifier has 4 channels on it. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The operating supply voltage of the buffer op amp is rated at 6V. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
MCP6L4T-E/SL Features
14 Pins
supply voltage of 5V
105dB voltage gain
Output Type: Rail-to-Rail
MCP6L4T-E/SL Applications
There are a lot of Microchip Technology MCP6L4T-E/SL Instrumentational OP Amps applications.
- Professional videography
- Laptop
- Automatic control
- Power transmission
- Signal operation
- Proportional counter tubes
- Non-polarized electrodes
- E-book readers
- Television broadcasting equipment
- Radar
