MCP6L4T-E/ST
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6L4 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Power Supplies | 5V |
| Number of Channels | 4 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 200μA |
| Output Current | 20mA |
| Slew Rate | 2.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 2.8MHz |
| Unity Gain BW-Nom | 2800 kHz |
| Voltage Gain | 105dB |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Height | 1.05mm |
| Length | 5.1mm |
| Width | 4.5mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6L4T-E/ST Overview
In order to protect the op amps, a 14-TSSOP (0.173, 4.40mm Width) case is used. There are two types of operational amplifiers in this circuit. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. We are approaching the 14h termination of the year. The pins on this board total to 14 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. It should be noted that this op amp is a type of Operational Amplifier device. 14 pins are located on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 3mV. This electronic part is recommended for mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. Operational amplifier can operate supply current at 200μA. Voltage gain should remain at 105dB. There are 4 channels on the operational amplifiers. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of the buffer op amp is rated at 6V. TAPE AND REEL is adopted to pack the instrumentation amplifier.
MCP6L4T-E/ST Features
14 Pins
supply voltage of 5V
105dB voltage gain
Output Type: Rail-to-Rail
MCP6L4T-E/ST Applications
There are a lot of Microchip Technology MCP6L4T-E/ST Instrumentational OP Amps applications.
- Blood pressure sensors
- Signal transformation
- Communication device
- Semiconductor detectors
- Gaming industry
- Portable media players
- Vehicle electronics
- High gain DC amplifier
- Computer workstations
- Switching amplifier
