MCP6L74T-E/SL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6L74 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 5V |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Nominal Supply Current | 150μA |
| Output Current | 25mA |
| Slew Rate | 0.9V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 91 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2V~6V |
| Input Offset Voltage (Vos) | 4mV |
| Bandwidth | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 105dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Height | 1.25mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6L74T-E/SL Overview
The linear amplifier is packaged in a 14-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. This is a General Purpose type op amp. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. During the past two weeks, there have been close to 14 terminations. It consists of a total of 14 pins in total. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. A total of 14 pins are present on the instrumentation amplifier. Op amp rates 4mV as input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. With regard to operating temperature, this op amp functions well at -40°C~125°C. It is recommended to keep the voltage gain at 105dB at all times. A linear amplifier like this has 4 circuits on it. Op amp ic has 4 channels. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The instrumentation amplifier is packed in the form of TAPE AND REEL.
MCP6L74T-E/SL Features
14 Pins
supply voltage of 5V
105dB voltage gain
Output Type: Rail-to-Rail
MCP6L74T-E/SL Applications
There are a lot of Microchip Technology MCP6L74T-E/SL Instrumentational OP Amps applications.
- Medical instruments
- Inverse/same-phase proportional circuit
- Non-polarized electrodes
- Comparator
- Test and measurement instruments
- Switching amplifier
- High gain DC amplifier
- Instrumentation
- Test equipment
- Wireless base stations
