banner_page

MCP6N11T-005E/MNY

1 Channels 10pA 80 dB Instrumentational OP Amps 0.005μA 1.8V~5.5V MCP6N11 8 Pins 8-WFDFN Exposed Pad


  • Manufacturer: Microchip Technology
  • Nocochips NO: 536-MCP6N11T-005E/MNY
  • Package: 8-WFDFN Exposed Pad
  • Datasheet: PDF
  • Stock: 408
  • Description: 1 Channels 10pA 80 dB Instrumentational OP Amps 0.005μA 1.8V~5.5V MCP6N11 8 Pins 8-WFDFN Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-WFDFN Exposed Pad
Number of Pins 8
Operating Temperature -40°C~125°C
Packaging Tape & Reel (TR)
Published 2011
JESD-609 Code e4
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Terminal Position DUAL
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Terminal Pitch 0.5mm
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number MCP6N11
Pin Count 8
Output Type Rail-to-Rail
Number of Elements 2
Number of Channels 1
Number of Circuits 1
Nominal Supply Current 800μA
Max Supply Current 800μA
Slew Rate 9V/μs
Amplifier Type Instrumentation
Common Mode Rejection Ratio 80 dB
Current - Input Bias 10pA
Voltage - Supply, Single/Dual (±) 1.8V~5.5V
Input Offset Voltage (Vos) 850μV
Bandwidth 2.5MHz
Average Bias Current-Max (IIB) 0.005μA
Power Supply Rejection Ratio (PSRR) 75dB
Supply Voltage Limit-Max 6.5V
-3db Bandwidth 35MHz
Non-linearity-Max 0.05%
Height 750μm
Length 3mm
Width 2mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

MCP6N11T-005E/MNY Overview


There is a 8-WFDFN Exposed Pad case package that contains the instrumentation amplifiers. Op amps are Instrumentation types of amplifier on the chip. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are located on this board. A total of 8 pins are present on the instrumentation amplifier. With regard to input offset voltage, instrumentation amplifier is rated at 850μV. For this electrical component, Surface Mount is the recommended mounting type. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. This op amp ic has 1 circuits. The op amp ic has 1 channels on it. On the output type, there are Rail-to-Rail different types of op amps. Op amp has total of 2 elements.

MCP6N11T-005E/MNY Features


8 Pins
Output Type: Rail-to-Rail

MCP6N11T-005E/MNY Applications


There are a lot of Microchip Technology MCP6N11T-005E/MNY Instrumentational OP Amps applications.

  • High input resistance broadband
  • Semiconductor detectors
  • Fission chambers
  • Logarithmic operation circuits
  • Proportional operation circuits
  • Measurements of Wheatstone bridge
  • Portable electronic products powered by batteries
  • Hand-held batteries
  • Medical imaging
  • Band-stop filter

Write a review

Note: HTML is not translated!
    Bad           Good