MCP6S21-I/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 6.4kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Other Analog ICs |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6S21 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Analog IC - Other Type | ANALOG CIRCUIT |
| Nominal Supply Current | 1mA |
| Slew Rate | 22V/μs |
| Amplifier Type | Programmable Gain |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 275μV |
| Bandwidth | 12MHz |
| Voltage Gain | 30.1dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Voltage - Input Offset | 275μV |
| Current - Output / Channel | 30mA |
| Height | 1.18mm |
| Length | 3.1mm |
| Width | 5.08mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6S21-I/MS Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. An op amp ic of the Programmable Gain type. Linear amplifier is delivered in a Tube case. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 4V. I would like to specify that this buffer amplifier belongs to the Other Analog ICs-type of devices. A total of 8 pins are present on the instrumentation amplifier. Regarding input offset voltage, buffer amplifier rates 275μV voltage. This electrical part should be mounted using type Surface Mount. With regard to operating temperature, op amp ranges -40°C~85°C. It is recommended to keep the voltage gain at 30.1dB at all times. A instrumentation amplifier like this has 1 circuits. On the buffer amps, there are 1 channels that can be used. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of the buffer op amp is rated at 5V. It is recommended to keep the buffer amps resistance within the range of 6.4kOhm. In this linear amplifier, there is also an analog IC called a ANALOG CIRCUIT.
MCP6S21-I/MS Features
8 Pins
supply voltage of 4V
30.1dB voltage gain
Output Type: Rail-to-Rail
Resistance of 6.4kOhm
MCP6S21-I/MS Applications
There are a lot of Microchip Technology MCP6S21-I/MS Instrumentational OP Amps applications.
- Television broadcasting equipment
- Measurements of Wheatstone bridge
- Signal transformation
- Power transmission
- Large motor controllers
- Tablets
- Television
- Multiplication circuits
- Voltage regulation circuit
- Band-stop filter
